Loud snap or bang
A spring failure usually announces itself with a sharp metallic sound, often when no one is using the door. That noise is the spring releasing its stored tension.
Same-Day Spring Service
Garage door spring repair and replacement in Colorado Springs
A broken torsion or extension spring is the single most common reason a garage door will not lift. It is also one of the most dangerous DIY repairs. Whether you searched for garage door spring repair or spring replacement, it is the same visit: Springs Garage Door Services removes the failed spring, installs a correctly sized new one, and verifies balance before the door goes back into use, the same day, across Colorado Springs.
Same-dayTorsion & extensionSafety-verified
Signs You Need It
How to know your garage door spring is broken
Springs are under enormous tension. When one breaks, the symptoms are immediate and obvious. Do not try to lift the door manually until it has been inspected.
Door will not lift
The opener hums or struggles, but the door barely moves or stops a few inches up. The opener is not strong enough to lift the door without the spring carrying the weight.
Visible gap in the spring
Look up at the torsion spring above the door. If you see a clear gap or two separated pieces, the spring has failed.
Door slams down hard
If the door closes faster than normal or lands with force, the spring is no longer counterbalancing the weight properly. Stop using the door and call.
Cables hanging loose
Loose or detached cables often follow a spring break. The whole lift system depends on spring tension to keep the cables taut.
Crooked door
One side higher than the other usually means a single spring on a two-spring system has failed and the remaining spring is doing all the work.
Spring Types
Torsion springs vs. extension springs
Almost every residential garage door in Colorado Springs uses one of two counterbalance systems. Knowing which one your door has helps you understand what broke and what the replacement involves.
Torsion springs
Mounted on a shaft directly above the closed door, torsion springs twist to store energy and unwind to lift the door through cables and drums. They lift the door smoothly and evenly, which is why most modern doors use them. When a torsion spring fails you will usually see a clear gap in the coil above the door. Replacement means unwinding any remaining tension with proper winding bars, matching a new spring to the exact weight and height of your door, then winding it to the correct number of turns and testing the balance.
Extension springs
Extension springs stretch along the horizontal tracks on each side of the door and extend as the door closes. They are common on older or lighter doors. Because each side works independently, a single failed extension spring often leaves the door crooked or binding in the tracks. Safe replacement includes safety cables that run through each spring, so if one ever snaps again the broken coil is contained instead of flying across the garage.
Root Causes
Why garage door springs fail
Springs do the real lifting every time the door moves, so they are wear parts by design. These are the most common reasons they break in our region.
Cycle wear
Every spring is rated for a set number of open-close cycles. A busy household that uses the garage as the main entrance burns through those cycles far faster than the calendar suggests.
Cold snaps
Steel becomes more brittle in freezing weather. Colorado Springs winters are hard on springs, and failures spike on cold mornings when a stiff coil is asked to move a heavy door.
Rust and dry coils
Corrosion creates weak points, and a dry spring adds friction on every cycle. Periodic lubrication during a maintenance visit is the cheapest life extender a spring can get.
Wrong spring for the door
A spring that is too light or too heavy for the door forces the opener and the remaining hardware to compensate. Correct sizing against the actual door weight is a core part of a proper replacement.
How It Works
Our garage door spring repair process
Every spring call follows the same four steps, whether the door has one broken spring or a worn pair.
1. Inspection and measurement
We confirm which spring failed, measure wire size, length, and inside diameter, and weigh the door if needed so the replacement spring matches the door exactly.
2. Safe removal and installation
The failed spring is unwound and removed with proper winding bars, never shortcuts. The new spring is installed and wound to the correct torque for your door.
3. Hardware check
Spring failures stress the parts around them. We inspect cables, drums, center bearings, and end bearing plates, and flag anything that should be addressed while the door is open.
4. Balance and safety verification
The door is tested by hand at the halfway point, the opener force settings are checked, and the safety reversal is verified before we sign off.
Safety
Why spring replacement is not a DIY job
Garage door springs hold hundreds of pounds of stored tension. A spring that releases unexpectedly during installation can cause serious injury. Winding a torsion spring with improvised tools like screwdrivers or pliers is how most garage door injuries happen. We use the right winding bars, proper torque measurements, and balance verification to keep the work safe, and the door is tested through full cycles before it goes back into service.
Pairs
Should both springs be replaced together?
If your door has two springs and one breaks, the other is usually near the end of its life as well. Replacing both at once avoids a second service call within months and keeps tension balanced. We will give you the honest call based on what we see. Not sure the spring is fully broken yet? The warning signs above tell you what to look for before the door strands you.
Cost Factors
What affects garage door spring replacement cost
No two spring jobs price out exactly the same, but the drivers are consistent: the spring system your door uses, the size and weight of the door itself, whether one spring or the pair is replaced, and the condition of the hardware the springs work with, such as cables, bearings, and drums. A heavy insulated double door needs a stronger spring than a light single door, and worn cables discovered during the job are worth replacing while everything is already apart. For the bigger picture, read our guide on what affects garage door repair cost in Colorado Springs.
Quote First
Clear quote before any work starts
Eyal inspects the door, confirms the spring type and sizing, and explains the options before anything is unwound or removed. You approve the quote first. If related hardware is close to failure, you hear about it on the spot with a straight recommendation, never a surprise on the invoice.
FAQ
Garage door spring repair and replacement questions
The answers customers ask for most before booking spring service in Colorado Springs.
A snapped spring cannot be welded or patched back together. Garage door spring repair means removing the failed spring, installing a correctly sized new one, and correcting anything the failure affected, such as cables, bearings, and door balance. If the spring is worn but not yet broken, preventative replacement still saves the door from a sudden failure.
No. With a broken spring the opener and cables carry weight they were never designed to hold. Forcing the door up can strip the opener, snap a cable, or let the door fall. Leave the door where it is and call for service.
Yes. We replace torsion springs mounted above the door and extension springs that run along the horizontal tracks, matching the replacement to the door's weight and lift system.
On a two-spring door, both springs have usually absorbed the same number of cycles. When one breaks, the other is often close behind, so replacing the pair keeps tension balanced and avoids a second service call. Eyal gives an honest recommendation based on what the inspection shows.
The main factors are the spring type, the size and weight of the door, whether one or two springs are replaced, and the condition of related hardware such as cables, bearings, and drums. You get a clear quote after inspection, before any work starts.
Broken springs are treated as an urgent call, and same-day spring replacement is the standard goal across Colorado Springs and nearby communities during business hours.
Coverage
Spring repair and replacement across Colorado Springs and nearby communities
Monument
Same-day spring replacement for residential doors.
Fountain
Fast response for stuck doors caused by broken springs.
Falcon
Spring service for newer subdivisions and homeowner doors.
Woodland Park
Mountain-area spring failures from cold-weather wear.
Manitou Springs
Quick spring replacement on a responsive route.
All service areas
See full coverage including Peyton, Black Forest, Palmer Lake, and Calhan.
Helpful Links
Related services and guides
Garage door guides
Owner-written articles on springs, openers, insulation, and repair costs in Colorado.
Two climates, two door problems
How Colorado's dry cold and Michigan's damp winters wear garage doors differently.
About Springs Garage Door Services
Who actually shows up, how work is quoted, and why the service stays owner-led.
Garage door replacement
When another repair stops making sense, here is how a replacement gets scoped.
Door Stuck? Call Now
Same-day garage door spring repair in Colorado Springs
Don't try to force the door. Don't park your car under it. Call and we will get the spring replaced safely and the door working again the same day.